-
Factory OEM LED Lighted Trunk Spoiler for GL1800 1st Gen
By Honda
- $289.99
-
-
-
Your Bike
Will this fit your bike?
-
Related Items
201 Member Reviews
1 Star: 1
2 Stars: 2
3 Stars: 0
4 Stars: 5
5 Stars: 193
Factory OEM LED Lighted Trunk Spoiler for GL1800 1st Gen
ITEM CODE: PG00029
10.27.2013
Great Spoiler and okay to install
I just put it on my 2008 pearl white Goldwing this weekend. I Also installed TailBlazer Rear Spoiler Brake & Running Light Modulator (K125LEDD). The installation went okay. The only thing I would recommend is to go out and purchase the size drill bits they recommend in the insulation instructions. The final bit I did go a 1/32†smaller which worked okay except for the wire hole I went with the size they recommended. The normal drill bit sets do not have the drill size they recommend. I used the template that was in the instructions but I notice they almost aligned up with the marks on the trunk (within 1/64 of an inch on two of them), so I used the marks. The marks worked great. I started with the small drill bit first from the underside of the trunk. When I went to the next larges drill bit, I tried drilling from the top side and it chipped the paint. Tape may have help but I didn’t try it. I did the remainder of the drilling from the underside of the trunk. The paint matched perfectly! |
Factory OEM LED Lighted Trunk Spoiler for GL1800 1st Gen
ITEM CODE: PG00029
06.17.2013
Great addition!!
I bought and installed this spoiler and man did it dress up the wing! Great addition and the extra light it provides is a bonus. The color was a perfect match to the Wing and it looks like it has always been there. I installed the Tailblazer Rear Spoiler Brake & Running Light Modulator and man does that light this baby up when you hit the brakes. If your thinking of buying one I don't think you would be disappointed. |
Factory OEM LED Lighted Trunk Spoiler for GL1800 1st Gen
ITEM CODE: PG00029
04.23.2013
Great Spoiler
I installed this yesterday (April 22nd) and followed the instructions along with the video by Cruiseman's garage on u-tube. Don't fret about drilling the holes. The template is off a bit, but so are the little 'dimples' on the underside of the trunk lid that Honda put there. You can use either the template or the dimples and you will find that drilling these holes to line up 'exactly' will most likely not happen unless you get lucky. Best thing to do I found was to drill according to the dimples then use a dremmel tool or small file to elongate the holes until the spoiler holes line up. They are covered well by the spoiler anyway, so you wont see them. The end result is a nice looking spoiler that will compliment your bike well. |
Factory OEM LED Lighted Trunk Spoiler for GL1800 1st Gen
ITEM CODE: PG00029
04.21.2013
Great Safety Addition
Put this on last fall and wired with a TailBlazer Rear Brake Running & Spoiler Modulator. I used a cordless drill to remove all the screws holding the inside cover. Be careful when drilling the holes. Using a smaller drill bit to start helps if you are off a bit. When wiring read the instructions carefully, one wire will need to be spliced into the running lights. The color matched my 2010 red perfectly. The brake modulator is a real eye catcher with the led lights. |
Factory OEM LED Lighted Trunk Spoiler for GL1800 1st Gen
ITEM CODE: PG00029
03.02.2013
doesnt get any better
Perfect color match perfect fit. Easy install just follow the directions and you will get a nice install in about a half hour. I have a blue 2012 and the color is spot on! |
Factory OEM LED Lighted Trunk Spoiler for GL1800 1st Gen
ITEM CODE: PG00029
02.20.2013
Looks great, easy install
Just installed the spoiler today, not a difficult task, but takes courage to drill the holes. The template was perfect, just take time to cut out the holes in template. I used an exacto knife which worked well. My install was on a 2012, there were "dimples" in the lid, but stuck with the template...looks great!! |
Factory OEM LED Lighted Trunk Spoiler for GL1800 1st Gen
ITEM CODE: PG00029
10.05.2012
Spoiler a must have easy install
Spoiler very well made it adds a great look and I replaced the light before installing spoiler with Item #:AO451842V Running/Brake/Turn Signal all in one light and installed the American Motorcycle Accessories GL1800 Chrome Billet Luggage Rack Item #:SBAMA2003 after for a total great look. SPOILER INSTALLATION WAS EASY I CUT THE TEMPLATE OUT WITH A RAZOR BLADE FOR A CLEAN CUT. NOTE: THE TRUNK WAS DESIGNED FOR A SPOILER IF YOU LOOK CAREFULLY AT THE UNDERSIDE OF THE TRUNK LID WHERE THE TEMPLATE SHOWS TO DRILL THE HOLES YOU WILL SEE MOLDED INTO THE LID 3 CIRCLES WITH A RAISED POINT IN THE MIDDLE ON THE LEFT SIDE AND 2 ON THE RIGHT. NOTE: I found the recommended drill size for the screws are too big so I used the size that matched the screws size for a tighter better fit. |
Factory OEM LED Lighted Trunk Spoiler for GL1800 1st Gen
ITEM CODE: PG00029
07.14.2012
Spoiler
Spoiler looks great and is a bonus to the bike. Pattern that came with it is way off. I had to redrill hole. Thank god the spoiler covered it.Worth every penny. Installed in 15 minutes and had the bike put back together and Iam no machanic!!Trust me on that. |
Factory OEM LED Lighted Trunk Spoiler for GL1800 1st Gen
ITEM CODE: PG00029
06.10.2012
easy install....but
beautiful addition to your wing. template for drilling was accurate and brake light hookup plug and play. if you already have a luggage rack installed check the mounting location befor drilling. i had to relocate the spoiler 1/4" rearward to clear the rack mount. |
Factory OEM LED Lighted Trunk Spoiler for GL1800 1st Gen
ITEM CODE: PG00029
05.29.2012
Spoiler
I have liked the looks of this spoiler. The one thing I wish they would have is a red lense instead of the clear to match the red lenses on my CSC Viper trike. The lights are red though. |
Factory OEM LED Lighted Trunk Spoiler for GL1800 1st Gen
ITEM CODE: PG00029
05.21.2012
Great added attention getting lights Pluse
Not only does this spoiler get rid of the sloped camel back look of the back and transform it into the sporty styling look the bike deserves but it adds a HUGE amount of attention getting, accident avoiding Brake Lights... especially if you tow a trailer or ride in traffic or at night. The paint was an exact match which was great, the fit is perfect and the plug and play made it a no brainer, instructions were very clear and easy to follow |
Factory OEM LED Lighted Trunk Spoiler for GL1800 1st Gen
ITEM CODE: PG00029
04.22.2012
Awesome item.
This looks so good on my 2010 wing! Installation was fairly simple. I found that the template was pretty close for the holes but there are 3 small (sand size) mould lumps exactly where you need to drill on each side and I just used these. Worked out perfectly. The brake light is very bright. I fitted this today and everyone who has seen it reckons it looks great. I doubt you will be disappointed if you put one of these on your wing. |