Contact Us
| Tried using the hairspray, did not work. Tried using some soapy water, did not work. Used some silicone spray and slid on rather easily! Small price for a big difference! |
| Shame on Wingstuff for not checking their stock. I ordered a 2XL based on a report they ran small. I got a circus tent. It must be a 4XL or more. The supplier should be fired. Now I have to ship it back at my expense. I needed it for a trip, so now I don't even know what size to order with a 47-48 chest. |
| I gave this a one star because there is no zero. Bought this flag, placed it on my bike on 8-20-11, white stripe through red area by 8-29-11. No More. |
|
As an American...I am proud to fly the American Flag (made in the U.S.A.) on my Goldwing. This flag endures the weather and sun very well. |
| I just bought this product. But, I'm sorry that it is sorry. The item it's self is well made. I mounted it on my Wing handlebars and on my first trip the acorn nut that holds the nut backed off and I lost my cup holder. It was well secure when I started. I won't buy another one |
| Looks great, installation wasn't that bad but not to crazy about how it attaches. Not sure it will hold up the velcro on the seat brace and frame is worthless as far as I can see. This is the 2nd item I have ordered from here and service and delivery have been great. Will continue to do business with these folks. |
| Just installed this Anti-Dive valve shim. Easy to install.Only ridden 150km with it on I also have traxxion springs in the front forks . This valve shim seems to provide a smoother ride over rough surfaces |
|
I'm giving them five stars because I'm sure they would have looked nice. However, they will not fit the saddlebag on a 2012 model. I only discovered this because I ordered many accessories before taking delivery of my bike and had completely forgotten what the bags looked like. |
|
Fits 2012 Gold Wing (mine has the airbag so it'll probably work on any model below that too). You will need a freakishly large drill bit (13.5mm). You can use a 1/2 bit when you enlarge the holes, but you will have to make it a tiny bit bigger later on. Slowly increase the size of the bit you're using so you don't rip the plastic apart. Installation takes just over an hour. Take your time and work carefully. They seem easy to install, but quite a few parts have to come off in order to put them in. Inner top trunk lid, rear passenger seat, main seat, speakers. To remove the old pads, there are four small posts with nuts. Carefully insert a very small flat blade screwdriver underneath the nut on both sides of it, bend upward. Next, use a pair of pliers to grab both sides and crush it. Repeat 90 degrees on the other side of the nut and crush the other side. They'll just pop off at that point. When you start putting everything back together -- take note of the screw that goes into the speaker from below, the one directly in front of the little cargo door. It needs to be threaded straight up. You can do this by opening the little door and using a stubby phillips screwdriver. A standard length handle is too long. Instructions were fair. They have illustrations outlining the process -- unlike most of the Kuryakyn instructions I've been working with for the past day. |
|
Very nice back rest. Big improvement over those with the bars. I used a bamboo skewer first to determine the angle the knife should go in at. You can easily see it through the seat bottom when you get it right. Use a big serrated kitchen knife like they show in the instructions. I only had to plunge it in once, and the bar went in perfectly after that. Be sure to tighten the pivot bolts so it doesn't flop around. pouch does flap in the wind, Some small pieces of velcro at the bottom corners resolve that. |
|
I like this stand a little better than the other large-footed stand I had on my previous Wing. The picture does not do this stand justice. I was hesitant because the picture looks like someone welded a spoon to the bottom. That is certainly not the case. It's a very nice fully cast piece. |
| This is my third Utopia backrest, I've had them on a 1984 and a 1999 Goldwing also. I put this one on a 2010. The installation is fairly simple as long as you follow the instructions carefully. (Measure twice and cut once) I really like the comfort on long rides. |