TOP REVIEWED
-
Rubber Baby Buggy Bumpers for GL1800
By Pakit Rak SKU: PRRBBB
- $12.99
-
-
-
Your Bike
Will this fit your bike?
-
172 Member Reviews
1 Star: 16
2 Stars: 10
3 Stars: 8
4 Stars: 33
5 Stars: 105
Rubber Baby Buggy Bumpers for GL1800
ITEM CODE: PRRBBB, SKU: PRRBBB
03.20.2010
5 Stars
These work great, trunk lid closes tighly now. Would recommend. |
Rubber Baby Buggy Bumpers for GL1800
ITEM CODE: PRRBBB, SKU: PRRBBB
03.10.2010
4 Stars
Yes, you have to drill holes in your "baby". Yes, they make it a little harder to close the trunk lid. Yes, the tips break off if you pull them through wrong (which is why they give 5 - one to ruin). But they work as advertised and the instructions and templates could not have been better. R.B.B.B.s rock! |
Rubber Baby Buggy Bumpers for GL1800
ITEM CODE: PRRBBB, SKU: PRRBBB
01.29.2010
4 Stars
I'm giving this a 4 star raring, not because they don't they work as advertised and the installation instructions were spot on! I just am not too sure after two weeks of installation if they will serve the intended purpose in the long run. The trunk shuts fine now after two weeks of use, put the bumpers have deformed and in the case of the right forward bumper it is now leaning back, the other three look as though they have been pinch into a vise. So I'm not too sure what I am gaining after deformation of the plugs. They look beat into submission. Not too sure how long they will stay with the bike before I come up with my own solution. For the price you can't beat them, but now there are four nice size holes in my trunk. If you are unsure about putting holes in your trunk, don't do it!! |
Rubber Baby Buggy Bumpers for GL1800
ITEM CODE: PRRBBB, SKU: PRRBBB
01.28.2010
3 Stars
These were hard to install lost one the first week how can you lose a plug in a trunk ??? I had them in for about 2 months but I have removed them. I had to slam the trunk lid and that was causing trouble with my trunk organizer. Most of the time shutting the trunk would not show it on the bike dash I would have to get off and do it many times. I fell this will damage stuff in the future so bye bye. |
Rubber Baby Buggy Bumpers for GL1800
ITEM CODE: PRRBBB, SKU: PRRBBB
01.24.2010
5 Stars
They were easy to install, only took about 10-15 min's. After install the trunk was hard to close, about a month later I used some sand paper to the right side bumpers, problem solved. |
Rubber Baby Buggy Bumpers for GL1800
ITEM CODE: PRRBBB, SKU: PRRBBB
01.23.2010
5 Stars
Good to go. It took longer to get everything out to install the bumpers than it did to install them. Yes the lid is a little harder to close and open at this time. I believe that the lid will operate easier just given some time. |
Rubber Baby Buggy Bumpers for GL1800
ITEM CODE: PRRBBB, SKU: PRRBBB
01.20.2010
5 Stars
Just installed them. I found that the rubber has some slow return memory so it helps to pull on them a bit and hold for a few moments to streach it a bit and then insert them and work it as described in the instructions. The trunk does fit tight and I hope it loosens a bit soon. |
Rubber Baby Buggy Bumpers for GL1800
ITEM CODE: PRRBBB, SKU: PRRBBB
01.15.2010
5 Stars
Just purchased these and put them on. Took about ten minutes. I found the spit method works best. It takes a little bit of effort but with long nose pliers they will eventually pull into place. The stem is very strong and didn’t break off even when I used a lot of force pulling them through. The pack comes with five stoppers even though you only use four so for those watching the pennies get your buddies together, order four packs and you can make up one pack free. |
Rubber Baby Buggy Bumpers for GL1800
ITEM CODE: PRRBBB, SKU: PRRBBB
01.14.2010
5 Stars
Just put these on the trunk this past weekend. Cut out the template, overlaid on the trunk as instructed, drilled smaller hole first (1/16") then drilled larger hole to make sure they were in a single wall thickness - and sure enough the template was right on! Spit does works best with a strong steady pull with needle nose pliers from below and firm pressure from above. Trunk lid is a bit hard to close, but should adjust over time. No more rubbing. This should be a standard feature from Honda. |
Rubber Baby Buggy Bumpers for GL1800
ITEM CODE: PRRBBB, SKU: PRRBBB
01.13.2010
4 Stars
I installed them after Xmas it was a little cold hard to install. the paper layout that you lay out for the holes to be drilled was off so make sure you can reach them from underneath. If you put them where theres a dubble wall they will be hard to get to from the bottem to pull them threw. Lost one already I do beleave they are about 1/4 to tall. The back ones are slanted over now. as long as my latch dosen't get damaged its cool. |
Rubber Baby Buggy Bumpers for GL1800
ITEM CODE: PRRBBB, SKU: PRRBBB
01.13.2010
5 Stars
Rattling sound from the rear is gone when riding rough pavements and it closes in a solid sound shut. When you open it the trunk lid pops up right away. |
Rubber Baby Buggy Bumpers for GL1800
ITEM CODE: PRRBBB, SKU: PRRBBB
01.08.2010
5 Stars
These work well to make the trunk close tight and not rattle or rub. Installing them is a little tricky, the saliva works but I also tapped them with a rubber mallet to get them to set. |