Contact Us
|
I got these on my used Wing at time of purchase. I had doubts if they were of any use and was contemplating removing them. Then I rode my 'new to me' Wing and I was amazed! Much of my riding is in cold weather and they make an amazing difference, so much so I wont' even bother to get heated grips. I had heated grips on my K1200LT and it left the tops of my hands/fingers cold but with these airwings deflecting the cold air away from my hands, my entire hands are warm. On occasion when it does get hot, you merely twist them and they funnel a lot of air into your still air cockpit to help alleviate the heat...amazing how much air you can move onto your upper body to keep you a bit cooler. |
|
I got this to replace the original cover here on my Wing that the previous owner had mounted something to (left 4 holes behind). Why this is a great product: 1. Very easy to install. 2. Plug and play. 3. Perfect OEM fit & finish. 4. Voltmeter is very functional and accurate. 5. Looks classy and is lit up/visible at night. Another item that you have to wonder why it isn't OEM from the factory? |
| It's an alloy that isn't as strong as the OEM. Don't put on with recommended torque or you'll never get it off and the metal just shears off! After my break in oil change I addeded this plug wanting the protection and piece of ming of the magnetic feature. Bad decision on my part I assure you. Some two hours later I got it out and in the trash it went! Also, they compromised on the bolt size (13mm v. 17mm), making it even more difficult to get ahold of it to remove. Believe me, I found out the hard way! |
| The 2012 goldwings dont come with the plug so why pay Honda to add it. This one is longer than the Honda part so if you want to route this to the trunk there is plenty of cable. |
| This is as basic as it gets. I used this to add a volt meter to my right hand side of the bike. Pluged into left side plug under pocket perfect length to right side of cowl for my added Volt meter. |
| Easy insatll drill a hole, snap into place and plug it in. About 5 min. It looks as good as the Honda part and fits the same place. |
|
Install went very well! I think it took longer to cut out the plastic fork cover then it did for the rest of the install. Love the risers they have me sitting up straight not leaning forward at all. I am 5'8". Well worth the cost. I would recommend them for everyone!!111 I have 2008 without the airbag. |
| Had a lot of fun installing this and drilling holes in my one week old to me 2005 Goldwing. The first steps in the instructions deal with removing the trunk...unless you really just want to take the time removing the trunk I recommend leaving it right where it is. The 28mm hole can be drilled from the saddle side. I was able 2 use an 1 1/8 unibit (step bit) and get it done cleanly. Because my Goldwing never had a CB and only 3800 miles on it after 8 years the switches and controls for the CB were a little reluctant at first but worked great after a days ride and jabber on the ride. Also please make sure you have the SWR set/checked on you CB antenna so as not to burn up a $600 CB with an out of spec SWR. |
| Installation was a breeze. just please be certain to make sure you have the SWR checked for this antenna. Mine was out and had to be shortened by about 5/8". I know this does not seem that significant but a CB with an out of spec SWR can burn up your CB, and at $600 for the factory CB this was a no brainer for me and a $20 bill at my local CB Radio shop. (Usually find them a Truck Stops). |
| Man, just received these in the Mail. Took about 15 minutes or so to remove the originals and replace them with these. They look very very good. Makes an entire side stand out. Wish I could have purchased this Chrome piece first before I purchased anything else. They look that good. So, what are you waiting for, go and order yours. You will not be disappointed. Trust me. What a perfect fit too. Thanks. |
| The Glove Box Cubby was a snap to install, but the cup holder is not very wide, you'll need to look for a small size water bottle fi fit. |
| I added these with the ISO grips and they complement them very well. |