Contact Us
| Excellent product for getting rid of that stupid weld cover, For the price of that bike ,you would think it would come stock (but who am I kidding) very easy install . A bit pricey but worth it.. |
| Add a bit more chrome , price is right , took 2 minutes to install , very simple , easy...... |
| Easy to install. Took me maybe 30 seconds. I never used that little compartment anyway. This takes its place and I love the location. The drink is directly in front of you and easy to manage. And there is no holder hanging from the handlebars, getting in my way. Since it's grounded in the body of the bike itself, it's sturdy. The interior is rubber, so I keep my sunglasses and phone in a couple of the compartments. You will have trouble getting a drink larger than a 20 oz. to fit inside the holder, although the rubber interior of the holder does have "fins" that conform to a bottle that is a bit larger sometimes. But you'll have to learn not to get a bottle that is shaped with a larger bottom to it. However, I have no complaints and I use it every time I ride. I keep extra bottles of water and Gatorade in the trunk and one of those is always in my holder. |
| Today September 6 2013 I recieved my second set of the dual Air wings. Both had no mounting hardware. I called Baker in OK City and they mailed me thye hardware for the first set. Called them again today, we will see if they send me another mounting kit. Very poor quality control. |
| I was surprised the difference this windshield makes. Love it. I have no complaints. Have driven about 1000 miles with it, still working on the correct height for my wife and I. She hasn't noticed a difference yet. Installing was easy and shipping was right on time. UPS dropped it off at my neighbors house. Funny story I was in the garage preparing my bike for the new windshield as I heard the UPS truck pulling away. I tried to wave her down but she wasn't even looking. I walked over to my neighbors house and there was the box.. Hard to find good help anymore.. |
| This is another of the few accessories bought at and installed by our dealer since we flew to Arkansas with intent to drive back to Houston via Waco (almost 800 miles put on that first weekend). The adjustability for tilt and height makes this a great accessory. I was happy they installed the back rest since we have the heated seats (made me nervous that I would damage a wire within the seat). |
|
Instructions ( Simple, Easy, and Clear ) Installation : Once you cut the template, tape it in place. Drill a Small pilot hole first. Then the 1/4 " hole. I took grease and put it on the bottom portion of the rubber buddy and in my holes i drilled. Then pulled on the rubber piece a few times stretching them. The front holes, pulled right thru with needle nose. The back holes i used a small screw driver to push them in. Worked like a dream. Shuts fine and the rattling gone. Some people just complain. |
| I loved the looks of these covers so much that I miss-matched the saddlebag accent trim intentionally since I did not like the half-trim. This is one of the few pieces that I bought and had installed at the dealer since I did not know about wingstuff yet since this is my first wing. |
|
Great attention getter! I removed the bottom cover of the trunk and mounted the unit to the bottom of the trunk. This makes for easy access to the trunk tail light wiring. The cover protects the unit and is out of the way and trunk. I drilled a 1/4" hole near the helmet lock for a 3 position micro switch to change patterns. If one wires their bike as I did, I recommend using red LED bulbs. The unit reports to handle only 10 amps. 4 - 7443 incandescent bulbs are right at 10 amps. I know, a little more involved installation but what else do I have to do beside chase women and ride? :-) |
|
I was excited to install these pegs for my (new) bride. I ordered them as a surprise for her, and had them sent to a friend's place. We planned to visit them along the way on our honeymoon. I thought Don and I could install the pegs in about 10 or 15 minutes without her knowing, then take her to the bike and shout "surprise!" Unfortunately, it didn't quite work out that way. We installed the LHS peg in about 2 minutes. The RHS peg was a different matter. The set screw on that peg (which is a "height" or rather, an angle adjustment screw) just wouldn't screw in all the way...it would get about halfway and bind. Fortunately, we could extract the screw and with a flashlight, we could see that there was a problem with the threads. The next morning (when the stores were open), I took a trip to the hardware store to purchase a tap & die set to attempt to fix the thread problem. Fortunately, chasing the threads worked, but the surprise for Cecile was "ruined." I sent an email off to Wingstuff, with photos of the procedure we performed on the footpeg, along with a copy of the receipt for the tools, and Wingstuff kindly covered the cost of the "repair," and then some. I'm glad we could get these pegs installed for the trip home (she loves them, by the way), and not have to return them for a replacement set. Thanks Wingstuff! |
|
I've upgraded my rating for the Oil Filter Wrench because I found a filter other than the Honda oil filter which works with this wrench - the K&N oil filter. The K&N filter has a 17mm "nut" on the top, which is the same size as the oil drain plug. Now I can remove both the drain plug and the filter with this single tool. I rated this wrench only 4 stars (up from a previous 1 star rating) because this wrench still won't work with the majority of oil filters, making it necessary to have another type of oil filter removal tool in your tool box. |
| As other reviewers have said, these are very nice, easy to install accents that make the front of the bike very nice looking. Down the road, I would like to add the lizard lights to really make these stand out at night. |