Contact Us
| Added lower cowl (AO451203) timing chain (KU3929) intake and radiator accents (KU3990 and AO451629NUB), WOW! Really finishes everything off nice. My buddy says it doesn’t even look like the same bike. I wish the radiator accents replaced OEM parts instead of taping/silicon sticking over the existing parts, but they have been on a while now and through a washing and seem to be holding fine. Just be aware if you are going to add a bra that you will want to do something about attaching the radiator anchor straps. The straps are supposed to hook to the grill, which might be fine on the OEM grill, but it will pull the chrome grill accent part of AO451629NUB out if you hook it there. |
| Looks great on the fender. Need to be real careful about placement. I used a whiteout pen to mark where to place it. |
| Did not sit flush on the fairing. So I used a 1500 watt hair blower to soften it enough to form to the contour of the fairing. Now I'll see how well it stands up to the elements and ride. |
|
Easy installation. I tucked the connectors in the space in the upper left. I covered them with plastic baggies and tape. I used a 6 pin connector because I tow my motorcycle trailer with my car. The tough nut was attaching the "bracket" side of the connector (pin-side) to something. I finally had to make a bracket that was bent over the hitch brace, which I secured with several tie wraps (not bolts) due to space limits. The connector bracket vertically bolts to the brace-bracket, which makes it easy to insert the male part of the connector. Plus the socket cover drops down and back toward the tire, protecting the socket from highway dirt. Hope this makes sense and helps. |
|
I read the instructions, which helped. Like 1 reviewer said, it was a little tight getting all the pieces to fit but they call came together. When I went to install the H-bracket (with the receiver) I couldn't tell which way to face it. One side has a bulge that hits the plastic box, so I turned it out. Wrong!! After I installed the license plate tupperware, I couldn't install the bolt who's boss is on the receiver that keeps the stinger from moving. So I took off the back piece, removed the H-bracket, and ground down ribs on the plastic box to take the bulge side of the bracket. Problem solved. Just FYI. Mine is an '08. |
|
Just ordered and installed. Thanks to wingstuff for same day shipping. Ordered and four days later received and installed. The pegs and mounts are of high quality and the design does well to limit slippage. A screw could loosen on anything but these are braced in several places. Very meaty design. I am still messing with the adjustments. I am 6'2 and have not found what I would call a comfortable position yet. |
| better look than black plastic,easy to instal,and you have to push hard on chrome botons to stay on there place,i never lost them |
| very nice looking and very easy to instal,i took onely 1 hour to do everything |
|
Giving this rating because it is cheap and should be sold cheaper. There is a significant glare issue with the clear lens. On a windy day, the lens is flimsy. If a rock hit it, am sure it would crack or break. It does add the protection from rain and cold air though. I bought it because I have a 3/4 OF and needed some protection from the rain and cold air. When the warm air gets here, I'll remove it. Snaps on pretty good and stays firm. It's a temporary fix, at least until I get a better helmet. |
| bought this bag for a trip. lots of room,fits well,stays on great. price is good. very well please.thanks |
| Very comfortable glove. Have only worn them with temps in the mid 70's and they started to feel a bit warm. We'll see how they are when it hits 90 degrees. |
| I put this hitch on my 2006 with few issues. It's a little tight getting all of the pieces together, but no major issues. I'm glad I had the directions from here, because the Add-On directions leave much to be desired. This looks like it's going to work just great, and at a great price!!! |