Contact Us
| I ordered this for my 2018 dct but I think it should come with the o-rings instead of having to order it separately since you need to change it each time you change the filter or at least have just in case it was needed. |
| I think Sena has done well with the 50s but even with the new update speakers it still falls short of the sound quality compared to Cardo even the cheap Freecom 2 has better speakers. On my 2018 Goldwing I have to raise the volume level to 14 to 16 while riding at highway speeds and I use a modular helmet. I ha d a Freecom 2 had a delay in CB reception and when using the intercom with my wife on the back of the bike it would work great but it would not connect back to the bike unless i turned it off and back on. I reached out to Cardo and was told that I would have to upgrade to the packtalk which I did and found that it had the same delay, So I purchased the 50s to get rid of the delay but lost on sound quality. Also when I use my cell phone with my phone connected to the blutooth on my bike I have been told several times by the people I call that the Cardo sounds better I will still give it 4 stars because it works good but not great. Also the blutooth stays connected even if you walk away (I have walked inside a building across a parking lot it stayed connected), |
| I bought these Tie Down Brackets and installed them on my Goldwing DCT because if I ever would be stranded and needed someone to haul my bike to a dealer, I wouldn't have to worry about how they would tie it down so it wouldn't fall over. These brackets fit perfectly on the bike and I didn't have to make any changes to the plastic covers. I have an air lift for the bike and used these brackets to steady the bike and they worked great. I would recommend these Tie Down Brackets because of their fit and heavy duty construction. |
| I used these pliers when I was installing the passenger grab rails. There was a small push pin that was difficult to remove. I could push the pin down but couldn't get it to come out of the hole. I used these pliers to pull the pin out. The pliers are very durable and easy to work with, because of the spring on the pliers. The handles have a texture built on them so they don't slip on your hands. They work well to pull up the push pins. |
| I added these grab rails because the stock ones didn't have much to hang on to or strap on a luggage bag. They were very easy to install including the lockable helmet piece. I thought it might be hard to install the lock but it was very easy to do. The grab rails look good on the bike now and I will use them for luggage on the passenger seat. I can now put the bike on the center stand easier with these grab rails. |
| These saddlebags liners fit very well. The Honda saddlebag liners were terrible with wasted space. Couldn't be happier to have these in the saddlebags. The liners were well made and will be durable for a long time to come. |
| This product was easy to install. I took my time and looked at all the bolts and where they were placed on the bike with the instructions. I mounted them in about 2 hours including the removal of the plastic covers and it took me about 45 minutes to adjust the foot pegs to my liking. I like the foot rests because they felt good with my boots and didn't have any issues with the boots moving off of the foot rests while riding. The instructions (fig. 7) pointed out to not install the arm at any angle less than parallel to the ground because it will scrape in corners. I thought that was very important to point this out. |
| I purchased the Utopia Driver Backrest because of the width and length . It didn't take long to install the bracket and the backrest. The instructions were very good and easy to follow. I would buy this backrest again if I purchase another Goldwing. |
| I absolutely love these highway pegs. Adding these pegs to my bike allowed me to ride that much longer with so much more comfort. I love how adjustable these pegs are and stable they are. Installing these pegs was not difficult. Just follow the video listed below and the supplied instructions. Also, make sure you have metric tools to assist in installing the pegs. https://www.youtube.com/watch?v=Fu3a7IkZZ4M |
| Installation of the drink holder was incredibly easy and the instructions are pretty straight forward. Following the instructions, adhere to the warning. Don't pinch the cables. My only recommendation, use some loctite on the top hex screw, if not the swivel arm where the ball is located at, will vibrate loose. However, the holder and mount are built well and functioning as it was designed. |
| Great product and super easy to install. Goes great when paired with the Twin Rail Floorboards. The cover adds just enough girth to make the brake pedal that must easier to step on. All in all, it's a must have to complete the look of my bike. |
| These floorboards are a perfect addition to the bike. They are big enough to comfortably fit most of my foot on it but small enough to not impede on the lean angle of the bike. I like the option of different mounting positions the floorboard offers. Installation was pretty straight forward, just watch the video link I included. The directions that came with the floorboards were a bit confusing. I gave these a 4 star rating as I had to modify/fix the left side bracket. I have to use my bench vice clamp to squeeze the prongs of the adapter closer together as they were a little too spread apart. https://www.youtube.com/watch?v=hQ88Hf6uU5k |
