Contact Us
| This junk rusts out every year. I have tried everything to stop the rust with no luck. I complained to Kuryakan with no results. I cannot afford 200 plus dollars a year just to change armrests. Don't waste your money. I have changed them out three times and they still rust. How come the cheap plastic parts still look good and the expensive stuff looks bad? |
| I bought this because it was pictured with the Rivco Armrests. The cup holder looks good but it is not of the best quality. It swivels and there isn't a way to tighten it to prevent it from happening. It finally fell off my bike while I was cruising one day. Fortunately it didn't do significant damage to my saddle bag (small scratch) but the holder itself was damaged and mounting hardware lost. I guess as it continued to swivel and I adjusted it, it became loose. I am very disappointed in this product and will not purchase again. 2 stars for looks only. |
| I bought this set last July and have been extremely satisfied. I put these on due to a poor performing set of E3's and you can certainly tell they are quite a bit quieter than the Dunlops. Have also noticed they seem to be a little softer compound and feel more responsive than the E3s. Ran 3 sets of E3s prior to these and I don't think I will be going back after having ridden these now. Only reason not a 5 star as I have not finished them off to see what kind of mileage I get out of them. |
| I added this to my 2012 GW to help cut down on the amount of cleaning/wiping on the lowers. Installation was easy. I did NOT remove the fender as the instructions suggests. Installation does require drilling two holes through the fender. I suggest using a 1/2" piece of wood to protect your front tire. This is one of those accessories that you will forget is even there, but will appreciate when you no longer have to clean the road crud from wheel splash. A must have if you want to preserve the beauty of your bike. This is NOT the fender extension the will crack your fender. That would be the longer, all chrome extension. Stay away from that model..... |
| After having put a fork brace and progressive spring on my 1500 and it becoming a brand new handling bike,, Adding it to my 1800 was a no thought requirement. Very easy install, it looks good and its a nice piece of chromed metal. I would be ashamed to this thing to loose it's glamor as someone else mentioned. As for performance, I will revisit after about 1500 miles. Why Honda doesn't put a fork brace on this bike I don't know. |
| Makes the back end look beefier. Nice look. |
| Well in looking at the recent reviews, Ernie from Lodi seems to have had the exact same experience and solutions.. I hardwired the pins to the connector and wrapped it real good with electrical tape so they wont come off. Then later found the connectors w/ the wire ties. Additionally, I had to drill out the whole in the cover with a 1/4' drill. The wires casing was just a little too thick in diameter. Other than that all was good. Nice light. |
| Kuryaukyn had their head on straight with this simple hookup item. Real helpful in leaving your knuckles and fingers unscarred after getting up into the fairing in those tight places. |
| Really easy to mount. I didn't use the "Brows" and it looks fine all by itself. |
| Nice looking piece. Measure, stick it and forget it. Simple and adds a classy touch. |
| I purchased the New Generation mirror mounted Air Wings for my 2012 to help manage or block the cold air blowing on the back of my hands. These made a big difference with the comfort level when temps are in the 40-50 degree range. I was actully able to use my lighter, thinner riding gloves with air being blocked or routed away from my hands. Installation was straight forward and only required you to remove the screws from under your mirrors to install the mounting studs. I tried the Air Wings at hwy speeds and the Air Wings didn't move. I chose the lite tint with chrome hardware instead of the dark smoke tint because I didn't want these to stand out. You barely notice them because you can see through them. I highly recommend these for anyone who encounter cold or even cool riding temps. |
| I bought these lights for my 2012 Wing because I wanted running/turn signal lights in a higher position on the rear. These lights are super bright and adds a little bang to an otherwise blank space. The installation was easy and only required removal of the seat to route the wires to the rear of the bike. Don't even think of not using the rear accessory plug. It really makes it Plug N Play. The instructions are well written. These lights solely rely on double sided tape to hold them in place. I suggest using a heat gun or blow dryer to warm up the mounting surface and tape to insure a solid, secure bond. Be sure to thoroughly clean the mounting surface with soap and water and then with the provided alcohol swabs to remove oils and wax build up. |