Contact Us
| No doubt about it, the very first addition to the bike. After one year the chrome is fading at the left mounting plate. I would not ride without these. |
| This should have been stock from Honda. Well made and sharp. Getting them off and on without scratching is challenging. Should have been designed as a bolt on. |
|
Iso Grip for Heat. First, I have owned many bikes and customized them all. I too am quite disappointed in this product. To the previous rider who did not line up the left notch, ouch, because you can rotate the interior notch to match the grip mounts, but alas, try getting it off without the thin, fragile grip not breaking! I had to buy another pair because one broke. When mounted, the grips do not match when observed, the adhesive is garbage, and useless. Additionally, for that price, some rings would be good. I give 3 stars because they are comfortable and allow some of the heat through. |
| Same complaints as everyone else. Crowds passenger and can't keep it tight even after torqueing the heck out of it. Constantly sliding backwards. Do yourself a favor and save the frustration. Don't buy this product. |
| WOW! What can I say. This is the first time I have been disappointed by a Kuryakyn product. I was very excited to see these new grips. There is a design flaw. The cut outs for the heated grip wire does not matchup. You have to line up the "half moon" supplied with the grips with a half moon cutout on the grip. The Rt grip goes on as advertised but the alignment problem on the Lt side drops this product by two stars. I still installed the grips, half moon NOT lined up, and they look great. However, the grip on the Lt side will rotate a little. They may come off after the first ride. |
| Great looks, well built, & very adjustable. I looked at and tried out a lot of highway pegs and running boards before deciding on these for my '06 Wing. |
| OK, I'm with some of the others as far as the wiring is concerned. I always like the easy way. That being said I am not afraid of wiring. This was easy to install on my 2006 Wing once I looked at everything. I only needed to remove the rear tire cover (where the license plate mounts) and accessed the wiring from there. Helps if you have the service manual. Look for the green wire with a very thin red stripe on both sides. You will have to add some wire. I located the unit on the left side and extended the right side wires to reach. LOVE the effect in mode 1. Definetly a good buy on this item if you can work on bikes. |
| IT WAS SIMPLE AND EASY TO INSTALL BRACKETS. A LITTIE BIT OF A PAIN TO INSTALL AND REMOVE. YOU HAVE TO BE CAREFUL NOT TO SCRATCH BIKE. THE WAY IT PIVOTS FORWARDS HELPS PASSENGER GET ON AND OFF BIKE. I HAVE HAD BACK SURGERY AND WILL NEVER HAVE ANOTHER BIKE WITHOUT ONE. THE QUALITY IS TOP NOTCH |
| The bag is made of good material. The lining is not overly stuffed, so the helmet fits easily. The zipper has double tubs so it is easy to open and close. Nice bag for the price. |
| Well looks like I will be the 1st of what I am sure will be many product reviews for this item. Let me start by saying I was pleasantly surprised when I received the Scuff Plate set to find that they were not made of ABS plastic with a chrome like finish. These are actually chrome metal. The written instructions are good enough, but if you pre-place them against the side bags, the contour of the plate will easily tell you where they belong. You need to make sure you have the correct set for each side. However, as I said, the cut and contour of the plate easily ID themselves. The plates adhere to the bags by adhesive strips and seem strong. The whole job took less than 20 minutes for me, but I am finicky about placement and look. One thing I wish the package did bring was alcohol pads to clean the area before final placement, but I had some extra ones lying around. They look great and if you have the chrome scuff covers attached as well, they really look good. What can I say Chrome is good! |
| I may not have used this the way it was intended but it suits my needs. I installed it in the left hand dash compartment along with the AUX input. I plan to use it to power a cell phone charger, MP3 charger, etc. Covered it with heat shrink tubing to insulate it and make it look a little nicer. There is a connector for it right below the compartment in the same harness as the AUX connector. |
| The Chrome Left Control Panel Accent, R/H Navi Control Panel Accent, the Chrome Radio Panel Accent, and the Chrome Radio Knob Set add a lot to the console are. Easy to install and dresses up the bike. Cheap upgrade that adds a lot! |