Contact Us
| I decided to give it a try and am very pleased with the results. I used to use armoral which works pretty good but this has it beat. A litte pricey but I guess you get what you pay for and it seems to be worth it. |
| Just finished installing these as well as the New Generation hand wings on my 08 Wing. Took it for a freeway ride and found that they work great just as the demonstration video depicts. I was solo at the time so I can't really comment on how they help the passenger. They are a five star item; however, I dropped one star due to missing parts. These are shipped directly from Baker so be sure and check your parts list before you start your install. I was missing four screws that attach the wings to the brackets. I called Baker and they sent some to me which I had in about three days. Only problem, they still shorted me two. Had to re-call and wait another 4 days before I could finish the install. All on now and working great. |
|
Got this for the back seat to keep the women happy. only problem its starting to rust. I have had it on for about 5 months now so thats not good. Other then the rust problem not to bad holds cups from flying into traffic. No more spills on the bike. |
| installed this for our laast summer, xmas 2010, put stainless and rubber washers on the top of the trunk, easy install. Very good product |
| great product, easy install even if a little scary, my wife like the backrest as it does not have the bars keeping her sitting position more comfortable. well worth the money |
| Recently installed this hitch on an 08 airbag model after emails to WS. Yes no real problems installing the hitch, as other have said keep the bolts loose until all bolts have been started and not cross threaded... Removed flat washers from lower part of H bracket then had to grind bolts down on the inner side so the rear plastic fender can be reinstalled and sit nearly flush again. Needs some redesign. Hence 4 star. |
|
Product is pretty nicely done but location makes the end result less than perfect. I am 6' 1" and ideally the seat would be farther back or up higher to stretch out a bit. I put on these pegs with idea that I could stretch my legs. The fairly is certainly in the way so you have kind of sharp end on you leg and thats even noticible with my pretty heavy duty riding pants I always wear. Assembly was mostly straight forward but there are 4 pins to pound into one part that took be forever to get 3 of them in as no easy way to push/pound them in given how part is set up. One went flying and I never found it so I contacted Kuryakyn via email today to see if I can get some replacements, will see how that goes. Clearance seems ok so far with them folded up. Certainly stick out some but cannot see them at all when riding and folded in. This is probably best choice for highway pegs given the challenge of the 2012 fairing design but do not expect the traditional highway peg set up, location, or comfort. |
|
Great product. I used it to manage additional rear and front lighting and have a spare switch. Installed on Brake resevoir and wired directly to the ACCESSORY terminals on the battery and put a 10A in-line fuse for good measure. I had to lengthen the cables to reach - and did it in such as way that they can be disconnected easily. Heed the warning about the fluid. Another great product |
|
Bought it, fitted it and it works. Don't know why Honda doesn't fit it as standard. My one bit of advise if be patient and if you've got large hands you may want someone to help who has petite hands. Good Luck. |
| I put one on each side tie wrapped to the radiator grill. Found out it gets a bit too hot and the hot glue inside the pucks melts and makes a mess. It's cleanable but now, not all the LED's are working. Don't put them near the radiator or anything hot. |
| I'm starting to wonder about Kury's commitment to quality control. I have two HD baggers with the chrome ISO's (but not for fitting over heated grips) and they have been fine. First off, they didn't finish the metal parts completely; there is bare unpainted metal where the collar fits over the rubber factory grip collar so I'm thinking they'll rust in short time. The rubber sleeves slid on easily (I used WD40 to assist). The metal clamshells are quite thin gauge metal and though I got the tabs to line up correctly, the grips "swell" in the center giving a slightly bulbous look (small space appears towards halfway point along grip). I 'gently' used a small-bladed screwdriver to fully pull the rubber extrusions through the holes in the clamshells. I WILL recommend these though because if you don't like the thin factory grips, or the throttle twitching that occurs when you try to maintain slow speed throttle at the same time as you're reaching for turn-signals, switches, etc., you'll like these. I like the diameter of these MORE than the ISO's on my HD's because of the slightly larger diameter. I installed with the over-sized throttle extension and it's a great combo. |
| Great plugs and super fast shipping from WingStuff! |