Contact Us
| It's all about the looks. |
| being 6'4" Most people say I look like I'm riding a sports bike instead of a wing, all crunched over., Handlebars hits my long legs in tight turns. Yep, It was a pain in the ARSE !!!!! I just installed the shims, OMG !!! what a difference !!! no more pain in the shoulders, not cramping in my hands. easier reach for the control buttons, and most of all the bars are no longer hitting my legs, I can now make tight u turns. It fells like a whole new bike. I'm loving it !!! |
| I have always used these. I do a lot of in town driving and at low speeds ( |
| I put this on the frame on the left side of the steering head like on the video. It works well and indicates as advertised when I checked it against a volt meter. I connected it to the power outlet in the left faring pocket and used a 2 pin connector from Radio Shack so I could disconnect it from the harness if I needed to for removal of the faring parts. I will asses it after the rain starts next week here in Washington to let you know if it holds up in the rain. If it survives the rain, then it gets a 5. I did use a little RTV to seal around the base prior to installation. |
| Received these covers in the mist of a snow storm here in Chicago and -30 degrees. Can't wait to install these to add to the other chrome I have already installed. |
| I recently purchased this set and was blown away. Fred really goes out of his way to make sure you understand each and every move. He's fantastic. At first I thought I was wasting my money, but after receiving them. I was overjoyed. If ever he comes out with one for the Honda Gold wing F6B I would definitely buy it. There is not much difference, but there is some thank you Jerry |
| anybody out there use this cover on a bushtec quantum trailer? if so how's the fit? |
|
I recently purchased a set of Kuryakyn pegs which I had yet to put on the bike. I saw these Rivco Aero Pegs and immediately put the Kuryakyn pegs on EBay and purchased these. Very easy installation even for someone as inept and mechanically declined as I. Use a hair dryer to help remove the OEM covers adhesive tape. With the CNC machined billet aluminum, this fits perfectly on the bike (looks like it came from the factory). Multiple setting points to accommodate inseam differences. Also, no worries about chrome flaking off over the years like with most other pegs. |
| In retrospect to my earlier review. If you have all three pieces of wiring these are a snap to install. I guess that is why K wants you to solder them in. One must be careful that you install them to have them look the same on both sides. Get your location on the first and make a cardboard template and reverse for the other mirror. Make sure all is working before closing up the rubber boots on the mirrors. The tiny plugs on the lights can install both ways but with different results. I am happy with mine but when you start out at the $50 range and end up at the $100 actual it gets aggravating. K wants you to buy the whole kit, signals and martini lights for $140. |
| In retrospect to my earlier review. If you have all three pieces of wiring these are a snap to install. I guess that is why K wants you to solder them in. One must be careful that you install them to have them look the same on both sides. Get your location on the first and make a cardboard template and reverse for the other mirror. Make sure all is working before closing up the rubber boots on the mirrors. The tiny plugs on the lights can install both ways but with different results. I am happy with mine but when you start out at the $50 range and end up at the $100 actual it gets aggravating. K wants you to buy the shoe kit, signals and martini lights for $130. |
| When I first saw this item I could not believe that Kuryakyn actually made something that cost less than $20.00. It looked very good on my 2003 Wing which was Platinum colored, so it should look even better on my Candy Red 2012. The install is all of about 5 minutes. |
| If you have the Superbrace between the forks on your bike, this will fit over the Superbrace, but there will be a gap of about 3/16 of an inch between the cover and the fender. Not a big deal. Still looks great. Also, you'll need to get longer fork cover mount screws to make it work. You'll need 6 mm X 1.00 pitch X 20 mm length cap screws. These are about 1/2" longer than the ones that come with this fork cover and are available at most hardware stores. |