Contact Us
| the leftside 8mm allen head bolt got rounded out. Could NOT remove it...the right side 14mm nut was VERY VERY difficult to remove..That being said the CRS stand is useless to me now... GREAT idea but, NOT an easy install.. |
| I got these a few years ago now. Still look brand new, no rust. So much easier to check air pressure and to add air. Why in heaven's sake these are not standard OEM on the GL1800 is a total mystery to me, especially for the rear tire being so hard to get at. Well worth the $8, a no brainer! |
|
Great Product. These are my second set as i am sporting a 2015 GL1800 now. and These are a MUST HAVE... Just make sure you READ ALL THE DIRECTIONS !!! As i was reading i did not have a 5/8 Flat Bit.So I ran to the hardware store to get one. To my Surprise they include the Drill Bit :( |
|
This thing needs a re-design to be just like the inter lid of the factory cover. Otherwise its not worth it your time, unless you are willing to Modify it like I did. The size is small all the way around by about 1/8th inch or more and looks like very cheap. Also it would be much nicer to be a flat black to match the plastic on the Goldwing. It is also missing the side tabs that slide into the factory holes. Nothing like the original. So I took the original lid parts and separated them. With the internal panel I cut the center out of it and ground it down to fit inside the Cubby Lid. I also had to cut the hinge tabs off the new cubby lid first and use the ones from the factory part. They will be bonded with a high grade epoxy. |
| These bags do not fit 2012 and newer models. Obviously the shape of the liners fits the 2011 and older models. I depended on a wrong description. |
| I have had these bulbs installed for a couple weeks now in my 2016 Wing. The installation video you can find of this product is wonderful. I installed them in about 2 hours from time of opening the box. I did find it helpful to have some Velcro strips with sticky on the backs. They do include 2 wire clamps in the box. Also when I installed my second bulb I put the boot on before I stuck it in the hole. You do have to cut a bit of rubber on the boot off but if you are careful it still seals up the bulb area. I have had no problem with the way the bulb reflects the light. And there is a lot of light. |
| Bushtec says this fits the F6B. Barely. I ended up replacing almost all the bolts supplied in the kit. The front mount bolt the right side was too short. The bolts that secure the upper braces under the seat were way too long, must be for the goldwing with a trunk. And all the grade 8 bolts in the back were too short to secure the nuts correctly. If you are like me and you want it done right, be prepared to make a trip to the hardware store. Pay attention Bushtec and make a F6B hardware kit. |
| I experienced a similar left side failure. A quality control issue from Kuryakyn's manufacturer. Were working for about 18 months. Glad they are easy to replace except for the cost. |
| Hitch is very study once installed. All the required hardware was not include, lucky for me I had the correct size nuts and washer at he the house and did not have to make a trip to the hardware store. Another grip is they advertise a stainless steel 17/8 inch ball but I received a chrome one. I will be complaining to Bushtec. Neither of these complaints are Wingstuff's fault as they do not stock the item, it is a direct ship from the manufacturer. |
| Another great product at a reasonable price . Quick and easy installation very satisfied with this product. The pads are justable about 1 inch fwd or back |
| Update to my last review. Don't buy it. I've ridden about 200 miles and it is really scratched up. I use only water and the same microfiber scratch proof rags that I use on an airplane window. Looks like I will be buying another windshield soon. Waste of money. |
| I wanted a black rack to stay with the blacked out theme on new wing and this one was perfect for me. Did not follow instructions as stated because I did not want to drill through both inner and outer lid. Worked great using the other brands instructions instead. |