Contact Us
| Instructions were clear and for the most part the pictures were clear enough to see the angles of the different brackets. Went together easy and looks good. The patch they give you that the bracket goes thru the seat looks good now, i believe that with time the ends will turn up and not look so hot.For now i am really satisfied with the look and the product. |
| After reading the reviews about loose fitment, I bought one 7743 bulb figuring if it didn't work well enough, I'd not be out so much. Turns out, it fits great and tightly into my 2010 Airbag model. It's definitely brighter than a stock bulb. I have ordered 5 more to replace all of my running/brake lights (total of 6). Also ordered 4 amber 7743's to replace the turn signals and an electronic load balancer. I'd say replacing the stock bulbs with these is a definite upgrade that while not inexpensive, it is worth it. |
| These lights are a great addition to the Goldwing! The installation looks intimidating, however, it was very, very simple. I followed the YouTube installation video by Cruiseman’s Garage which made the install flawless. The lights fit the lower cowl like a glove. Not only does it improve the look, but the additional light output increases your ability to see down the road as well as to the sides. This is the perfect compliment to the LED headlight conversion. The integrated daytime running lights and amber turn signals are the icing on this cake. |
| I purchased this item for my 2012 GL1800. I mounted to my Rivco hitch frame using the two holes already drilled in the rear of the hitch. I had to modify the holes in the bracket included with the Mud Flap to fit. The finished install looked great. The LED light is plenty bright. However, it didn’t last long. An hour into my maiden ride on I95, I hear noise and felt something strange and pulled over to inspect. The flap was sucked into the rear tire when I passed an 18 wheeler and was completely destroy. Perhaps the mounting location had it too close to the tire. I may try it again. I hope they will make one for the Gen 2 as it has gained popularity since the release of the 2018. |
| I bought this windshield for my 2004 GL1800a, First I started with the windshield all the way down and noticed a lot less pressure on my shoulders,Still a bit of wind on my face and buffeting. Then I put the windshield all the way up there was much less wand and buffeting, also a lot less air on my hands and legs. After 40 mins in the up position I lowered the windshield back to all the way down and was very happy with the air movement. Bottom line: If you don't want any wind on you when you ride then why ride? |
| Great to use for topping off. For doing a flush and change,I go to the Honda car dealership and a gallon is 20 bucks. |
| I received this bulb from Wingstuff and installed it yesterday. I’m giving 2 stars because the light output was great and fit well in the socket. However, I rode roughly 20 highway miles and when I got home the light was out. I took the lens off to find the end of the LED had broke. Upon further inspection, it appears that the end of the LED is held in place with solder alone. I’m assuming vibration broke the solder. I was able to repair it by re-soldering the ends on both sides. We will see how long it holds. If it breaks again, I’ll replace it with an LED from elsewhere. |
|
we have two Gl1800 gold wing bikes both with foot pads always kept in garage one had foot peddle bubble and chrome separation contacted wing stuff who gave us kuryakyn contact. 3 years on bad set 5 years on good set. one year warranty only . Some foot pads have issues. we were oferd a 10 % discount which is so close to wing stuff vip value meant nothing. Not sure if Kuryakyn are supporting there product. |
| Just like others have stated, audio quality is very tinny. Factory GPS, stereo, CB are very hard to hear clearly. My phone will Bluetooth perfectly and audio is excellent, but anything connected through Blu<>Hub is poor at best. I have wasted approx $1000 on this and Bluetooth headsets, save your money. |
|
So i purchased this when i purchased a new Road-Sofa Seat for my 86 GL1200a I wish i would have purchased this when i bought the bike and often ask myself.. Why didnt honda incorp something like this in the bike. to my knowledge even the new bikes the trunk is not adjustable. So why do i love this... Move the backrest back far enough that now we have to be fully bundled up before things start getting cramped. a short ride for us is a couple hundred miles which we do weekly if not several times a week.. So if your feeling a little cramped in the front seat buy this and you wont regret it one bit... Super Easy to install and all the hardware is correct and not cheap bolts or spacers like some products. this one they got it right... |
|
86 GL1200A -- so i never get to use this as i purchased them for my wife who is always my passenger. She tells me she loves the added comfort. her problem was her hands would swell on long rides but now that she can easily rest her arms and hands higher she is enjoying it.. The benefit to me is i get a back rub more often when riding now and a happy wife is a happy life. now for mounting. I'm not sure i really like the way they are designed to mount. single bolt mounting point which allows the rest to rock slightly. There are holes that match up to the hand grip that i could attach a u-bolt which would stop this but there is enough of a gap that I'm not sure i want to do this. I'm waiting to see if the bolt loosens at all over time and if it does then a solution will have to be made. As for the product i wish the tension bolt that allows the arms to tilt out and in was a hand tension bolt that could be adjusted without having to get out the wrenches... other than that i would say i love this add-on.. |
|
so much like the other review here i have a 86 GL1200A the hardware to mount this is VERY substandard so here is my recommendations When you receive these take the time to tighten the deflector to the mounts. then head off to the hardware store and spend roughly $12 to purchase new hardware for mounting to the wing.. Purchase some machine screws washers and rubber washers as well and then a decorative bullet nut for mounting Drill the hole to match your screw size and put it all together and tighten everything up. After trying to use the supplied hardware i was so frustrated but once i did the above i was very happy. |