Contact Us
| Easy to mount and look good. |
| These made made the bike look realy good. Make sure you have a extra set of hands to help you mount them. |
| The riser made it easyer the mount the luggage rack. |
| The rack was'nt hard to mount on the bike. What made it easy to mount was the raiser. |
| Boards sit too far aft. can't get your toe under the toe shifter. The heel shifter is anything but a natural move to shift. Too far back and too low. They should make the shift bar&pegs adjustable. I will probaly go back to the pegs as none of the other floor boards look any better. They just are not that comfortable. I'm 5'10" w/9.5 shoe. PS: Don't forget to screw on the toe peg before installing the left floor board. or you will have to remove it again. They forgot to mention that in the directions. |
| Plastic. First thing out of the box was a note letting me know that the manufacture was infallible and they could not make any mistakes. I have convinced myself that mine was broken in shippment and that the missing parts escaped and resealed the bad on their way out. On a side note be careful putting your GL1800 (and maybe others I am not aware of)on a condor motorcycle support (https://www.condor-lift.com/). The support will hit the cowl and could break the cowl. |
| Installed last night, when out this morning and my hands really appreciated the new grips. They look way better that stock. Would have preferred them to be a lot heavier than they are. Install was easy |
| This helps to keep small things organized. Easy install. Nice addition. |
| Looks like 5 stars but it does not give me the room I had hoped for, that is why it got a 3. Install was not bad but it should come with instructions and/or pictures of installation. It could be confusing trying to figure out what goes where and how. |
| Perfect lenght and nice snug fit. A little two snug for the larger connecter. I have a VERY hard time connecting the larger end because the dust cover is almost the exact same size as the connector on the bike, therefore it takes a unusually large amount of jiggling and wiggling to get the dust cover over the bike's connector. Seems to me that the inside edge of the cord's dust cover should be bezeled for easier connections. |
| These rests look extremely nice installed. Instructions are better than average for Kury, but expect to take 3 hours or more for installation. When I opened the package, it didn't look like it was gonna take that long, but it most certainly did. My brackets didn't sit flush in the side pockets and called Kury about it. They wanted me to return the whole unit to the dealer (about 100 miles away) for a new one. When I got BACK to the dealer, the brackets were identical... thanks Kury for a reason to put another 200 miles on my bike. However, as a note, after everything was tightened down, the brackets seemed to bend and twist a bit for a tight fit. Measure twice, drill once. My best success with the bracket was to set it flush on the bottom and the back, leaving the outside pressed against the pocket wall, but not flush. When you drill your holes on the outside of the pocket, drill a little further in and use your drill bit to "mark" your drill holes on the bracket. Use a very small bit for a pilot hole to prevent "bit drift" so that you don't have to ream holes out to make a good fit. You can use a sharpie marker instead of a center punch if, like me, you don't have one. When drilling on the left side of the trunk (if you don't have a CB already), use the little raised nipples on the inside of the trunk as your guide. Again, start with a small but for a pilot hole and use masking tape on the painted surface to prevent scratching from the drill shavings. My wife loves these arm rests. The drink holder is adequate and very nice if you use the supplied koozie. It is true that if you want to fully access your trunk you have to swing these out, but with them in, you can access your trunk about 12 inches. Not enough to put your helmet in, but more than enough to retrieve smaller items like gloves, mail, etc, but if you want it to stay open, you have to swing the arms out. One last item is that you WILL LOSE your stock mounting position for the passenger audio cord bracket. I did NOT like the idea of wedging it between the seat and the pocket, so I moved the bracket to a horizontal position just above the bottom of the left passenger pocket door. It looks pretty stock there and keeps the cord from rubbing on your bags. If you do this, make sure that you measure your holes so that when you open the pocket door, it will go all the way down. Feel free to contact me for a photo of this. [email protected] Almost 4 stars for Kury's ignorance to the 1800 bracket fitment issue, but since it looks so nice and still installs tightly, it gets the full 5. |
| Very easy installation. Product picture does not do the actual part justice. |