ON SALE
-
Black LED Accessory Switch
By Show Chrome
- $62.99Save $11.96
MSRP: $74.95
-
-
-
Your Bike
Will this fit your bike?
-
43 Member Reviews
1 Star: 0
2 Stars: 0
3 Stars: 1
4 Stars: 5
5 Stars: 37
Black LED Accessory Switch
ITEM CODE: PG20158
08.06.2020
[email protected]
The product is very excellent and I would recommend buying the product |
Black LED Accessory Switch
ITEM CODE: PG20158
08.04.2020
[email protected]
It is an excellent and wonderful product |
Black LED Accessory Switch
ITEM CODE: PG20158
07.31.2020
Excellent product
It is an excellent and wonderful product |
Black LED Accessory Switch
ITEM CODE: PG20158
07.25.2020
BLACK LED ACCESSORY SWITCH
Very reliable and awesome switch and it looks great on my handlebars. Never gave me any issues on my 2012 GW till today and i am buying one more to fix on my 2016. |
Black LED Accessory Switch
ITEM CODE: PG20158
05.13.2020
Good production
A beautiful product that arrived with excellent packaging speed and is being installed |
Black LED Accessory Switch
ITEM CODE: PG20158
03.05.2020
Great Product
Awesome makes the bike look a whole lot better and convenient for turning aux lights on and it sits out of the way and very handy for using!!!!!!! Awesome product!!!! |
Black LED Accessory Switch
ITEM CODE: PG20158
02.15.2017
excellent product
This switch assembly is greatly manufactured. It looks good on the handlebars and works great. I hooked up accessory lights to it and hooked up front end ring of fire. Handles load and works great. |
Black LED Accessory Switch
ITEM CODE: PG20158
05.07.2016
QUESTION !!!!
I have this on my bike, but I don't know where the wire ends up? Is it under the seat?, in a compartment? Behind a compartment? Mine is installed on my left handle. Thanks in advance for any assistance. |
Black LED Accessory Switch
ITEM CODE: PG20158
11.13.2015
Safety in mind!
I purchased this item for both my bikes. If you have followed my reviews up to this one you will see I am a big advocate of chrome and bling. Please note! In the cockpit of my wing I want it "BLACK" or dark. Don't want shinny object reflecting back into my eyes from the sun. I went for the left side install. This way I don't have to remove my hand from the throttle. Also, it's easier to run all your wires down the handle bar arm and into the area under the left pouch. Another hint to help you fellows constantly opening the side battery cover, I mounted a fuse block on the back inside wall of my truck. I simply run a wire from that fuse block to my power wire and switch wire under the left pocket. This way when you blew a fuse or need to review the aux. fuse block it's handy and easy to get to. |
Black LED Accessory Switch
ITEM CODE: PG20158
08.07.2014
Clutch Side Master Cylinder Switch Block (LH)
Just a concern before I placed my order for this product was the wire lengths leading from the switch block. Switch leads out are approximately 31" each on blue, yellow and white wires. Power leads in are 67" in length on red and black wires. All wires are covered by a soft/solid (not spiral or corrugated) PVC loom that will extend down the handle bar run. "Accessories may require their own relay and wiring as switches are rated at 20 amps." This quoted from install instructions. Looks like OEM, great fit and finish. Mike |
Black LED Accessory Switch
ITEM CODE: PG20158
01.19.2014
Re: Great Looking - Installation Problem
I installed the black switch box over clutch side. The switches quality is outstanding fit & finish and there was no leakage. The wire blue, yellow,and white were minimally 12" too short. Obviously, this extended my overall installation time to two hours to extend wires. Added length was necessary for me to allow wires to be fully routed and hidden. All wires all colors should be the same length as red and black allowing the installer to shorten depending on application and route installer prefers. Small indicator lights make sighting easy and no confusion as to what light is on. Switch block definitely has oem appearance. I'm happy with end result. |
Black LED Accessory Switch
ITEM CODE: PG20158
06.10.2013
Excellent Design
I have just installed these and they work and look great. I removed the switches from the housings (Right and Left) and sent them to ww.mywingbling.com to have painted. Very easy install. My only advise would be that prior to loosening and removing the fluid cover, loosen the bar mounting clamp so you can position the fluid housing as level as possible. This will eliminate any fluid from seeping out onto the paint. But if by chance it does happen, make sure you have alcohol and a rag near by to clean it off ASAP. Otherwise it will damage the paint. I have put a picture of the switch on my profile. |