Contact Us
| I really like this cover. Just went out and put it on my MotorTrike and the fit was great. I had no trouble putting the cover on by myself, but found it easier to leave it zipped up and stretch in over the front then down over the back. I have the aquashields on my trike and it is quite low so I probably won't hook the straps underneath, but it they would reach if needed to. I have never had a zipper before but like the idea of being able to access the trunk without removing the cover off half of the trike. |
| Just put them on my trike. Easy to install and look great with the lower vents. I am ready to buy more chrome accents. Love that bling! |
| These are great! Only took minutes to install. I only had to remove one since the left stock vent is on a highway somewhere where it flew off my trike. The chrome look is much better. |
|
Here is a product that has a great price, fantastic look and is easy to install. I like to give credit where is earned and the video's are usually very helpfull but in the this case it is terrible. If you have not installed the adapter with another addition you will need to purchase it. If you want to make that middle section on your bike shine this is the part you need. |
|
Just finished installing on my 2007 GoldWing. Nothing really difficult about the install, and the updated installation instructions were a big help. Took a total of 3 1/2 hours, a lot of which was simply getting bolt holes to line up. The hitch feels really solid and secure. Now I can mount my Golf Bag rack to the hitch! |
|
Installed this.. very straightforward but follow instructions. I do suggest using an alcohol swap to clean the seat where you stick the gasket on so it gets a good stick down. I also trimmed mine a little top and bottom so it didn't hit the seams and not sit right. Then take the alcohol swab and then wring it out so you can take a drink before you cut the seat. (the scary bit) It takes time to knife out the foam so go slow. It is so comfortable I cant beleive it. I will also be sealing around the cut to avoid water issues.. Also I am concerened about the square corner where it folds forward this could slowly dameg the seat over time. Will tape this to avoid.. damaging the seat. Really pleased with it.. Ray NZ |
|
I installed this at the same time as fitting the OEM spoiler. Install is easy and straight forward but do read the instructions carefully. I also suggest that you feed the cable "up" from the rear rather than down from the top. That way you are only dealing with a small end on the cable not the plugs. Caution the cable is only just long enough so don't put the cable ties on until finished. I had a problem .. no running light. Contacted EC .. Lewis answered almost immediately. Problem solved, it appears that some model GL1800's exported, don't have saddlebag running lights (mine doesn't, I'm in New Zealand) in which case you have to cut the black wire and join it to the tail light feed (its right there so no extra wire needed) ... problem fixed.. EC may need to update instructions to allow for overseas clients. Top support from EC & Lewis I couldn't ask for more. Very pleased with outcome.. by the way also used two small bits of double sided tape to help share the load off the little brackets. Ray NZ |
| I installed these myself following Honda Service Manual instructions. This job takes some time but the results are well worth it. Wobble is gone. This product exceeded my expectations. Hint: The wing forums are helpful with special tool workarounds. |
|
Nice looking product but is not worth the 9 bucks. It's not made in the USA. The snaps are junk cause when I installed the holder I accidently bumped the holder and 2 snaps came undone. Resnapped the snaps and did a test bump !!! same thing happened. My co-rider suggested that I put a little silicone in the snaps. It won't come off now. It is on forever untill I take a knife and cut it off or pry the snaps apart. This is a feeble attemped to correct the holder (that is junk) so that it fits . I am going to give a 2 star for It will hold a cup of coffee or soda can from your local Java shop. |
| Added after 200 mi on new 2010 GL1800. Changed oil at 2100 mi (I change sooner than factory recommendations on all my vehicles) & found very, very fine metal particulates, like etch-a-sketch matl ;-) This is normal for engine components seating, like rings, bearing surfaces, etc and will hopefuly reduce wear on the engine. Will replace the tranny plug now. |
| Just the right finishing touch to the rear fender! Appears to be very nice quality chromed metal (and as I always say- time will tell about the quality of Kury's chrome plate process ;-) Very easy install! |
|
Special thnaks to Don (GM) at Wingstuff for taking time and treating me like a valued customer! BG |