Contact Us
|
I added these to my new 40th Anniversary Goldwing. As some of the other reviewers have noted, these will definitely add visibility to the rear of the bike. I wired these up so they work with my Wig-Wag module for brakes and work with my turn signals. Ride Safe - Have Fun |
| I bought my first pair back in 2009 and I just had to buy another pair. they got holes in the bottom of the boots. I would recommend these boots to all. love how they zip up and then Velcro close very comfortable. worth the money. |
| Unlike other reviewer--MINE WORKS !! I purchased to install because I added Hartco Sheepskin covers and felt like I needed a heat boost because of thickness. It worked !! As far as hampering seat re-install like in other review--must be the seat installer--I had NO problem,went right back on no problems. I recommend product. |
| I love these grip covers!the stock grips always seemed a little to small for my hands these grip covers make the fit perfect they work well with my grip heaters and feel great riding down the road. I use compressed air and they slip right on. I ride my bike just about everyday and they have held up very well and are reasonable priced. I'll have them on my bike for as long as they are avaible. I'm about due for a new set I'll be ordering two. |
| Total crap. Don't waste your money. |
|
As with the new style engine guards it took a brain to install. It is made exactly the same as the factory one which is also tricky yo install it really helps to remove front wheel and fender and do the center first re-drilling don`t work because then the other parts won`t lock in correctly above it I tried that. After the center is in about halfway make sure the hoses are not binding then do the right loosely then left then tighten center again check hoses you might have to push around a little then the other screws an it will be correct again I measured an old one and the new one they are the same. |
| Has anybody tried these on a trike. I think the trike ones are little to gaudy or ugly. |
|
I just put these on my F6B. I can see why someone might think the foam is a problem.....but it's not. Not if you go about the installation in the right manner. RESIST the urge to reuse the OEM lens foam. Not only is it lightweight and fragile....but if you're taking it off of your original lenses which have been already installed....then it's probably nearly worn out anyway. The trick to the supplied foam is not to install the lenses into the housing...but rather to install the housing onto the lenses. First, ground the foam with your fingers and press it down as flat as you can. It is a memory type foam and will slowly spring back. Next...Install the lenses on the mirror frame, aligning the holes for the screws with the holes in the frame. While holding the lens in place on the frame...slowly but firmly work the housing onto the lens. It takes a little while as you have to be slow but firm...but the housing will go into place. Once installed....the memory foam is a FAR better seal against the elements than the cheap Honda foam ever was. It will expand and fill any open crevices between the lens and the housing..sealing it tight. The amber bulbs are not nearly dark enough. But that is about the ONLY bad thing I can say about these so far. Speaking as an engineer, I VERY rarely get to say that a product has been properly designed. This one fits the bill, however. |
| Great speakers....better than stock.Easy install if you understand how the tweeter connections and ignition plug get detached from the front panel.I advise you to go online and pull up some information on how to remove...a couple little tricks will save you some frustration!! |
|
Bought the right and left side panels and of course a few other chrome goodies. After a few weeks the right panel lost a chip of chrome about the size of a dime. Never had an issue before with anything from Wingstuff. Called to get instructions on return. Mark said no problem that he would send me a new one at no cost. Wow! Great customer service. Thanks Mark. Thanks Wingstuff! |
| I just received this rack system to install on my 05 and I am having to make some modifications to the hitch. The instructions call for on years 06 and later to cut a bit of a tab on the backside of the fender, which I had to do on my 05. No bid deal. But following those instructions, the fender still did not fit back on and was hitting part of the hitch. I had to grind off about 1/4 of steel from the upward part of the bracket by the u-bolts. I see that this hitch is back ordered now and the current picture looks different than what I received. Is this the reason? I don't know. Other than a little modifying, the hitch and 11 X 17 cooler rack that I also bought is made well and is a great design. Time will tell. I just wish it was a "plug and play". |
| Please see my previous review. I contacted Wingstuff and talked to the manager, Rodney, and his primary concern was to make certain I was taken care of. Wingstuff immediately sent me a new voltmeter as well as the new wiring harness. I returned to the dealer who had originally installed the voltmeter and the voltmeter and back light are now working fine. The dealer, Champion Powersports completed the additional installation at no charge. Thanks to all. I would suggest that special comments be made relative to the installation of this unit on 2010 Goldwings. |