Contact Us
| Installed 04.10.10: Works great; Keeps phone charged while riding. |
| This is perfect so far. It should be included in the floorboard package. I used it on the factory kickstand and it is under the floor board and the crome tip sticks out. I can not imagine anyone laying their bike down far enough for it to scrape the ground. So far no signs of it getting loose, but the tool that came with it is in my tool bag. Very easy to install. Solves the problem of raising the floorboard to put down the kickstand. |
| I use my cup holder all morning when I am on long trips. I usually ride with some Harley riders and this item bugs them even more than my stero system and heated seats and heated hand grips. I found no safty concerns with using it on the highway. |
|
This hitch fitted with little trouble, but left the saddlebags slightly splayed - took some wrestling to fit the fender back on. The worst part was the hitch falling apart after some7000 miles (11000 km) on Australian highways. The metal tubes of the H frame cracked through and broke adjacent to the welds at the bottom of the receiver. When they let go, luckily at very slow speed, the H frame bolts sheared. Had to get a steel reinforcing plate bent up and welded on to strengthen the repaired hitch before I could go any further. Also fitted tougher bolts. This all cost me a little money and an extra night on the road - all up, about the cost of the hitch. Not good enough, guys! |
| Very nice quality i ordered the indiana state flags mounted above the red white and blue look awesome. |
| Took all of ten miniute,s to drill and pull these through the holes they seem to work great Like the snug fit. |
| Less than a year old, and one of the headsets (drivers set) has developed a loose wire in the plug on the helmet. I have looked into all and that has to be where it is, connector wire is good on other helmet, will see how Wing Stuff handles this. Will let you know the outcome, stay tuned. |
|
I installed theseacouple of weeks ago. My rear passenger loves them. The only difficulty with my installation came when I attached the cushions to the swing arms. I recommend starting (and then removing) the screws in the cushions before attaching the cushions to the swing arms. |
|
Installed this harness a couple of weeks ago. This product performs well and I've achieved my objective of substantially improving the visual impact of the turn signals when viewed from behind. The instructions are reasonably clear and none of the steps are too challenging. However, some guidance re. what to do with the excess wire and the connections at the rear of the bike would be helpful. The lack thereof causes my taking away 1 star in the rating. I have two observations regarding the excess wires and connections in the rear. First, the black connectors on the wiring that you will attach to the trunk lights don't fit into the light compartment itself, so don't bother snaking them up there. Second, the relay box and excess wire in the harness need to be affixed to the framing down as low as possible underneath the plastic body part where the license plate is mounted. There is not any excess space available between the upper section of this body part and the frame. |
|
Installed this rack today. Great look on the bike! I found the installation instructions clear enough for a change. There are a few things I'd suggest: 1. Clarify product description on the riser topic. Based on reviews I ordered a set - and didn't need them. 2. Provide star washers to ensure the load is spread on the lid. 3. Some might find drilling holes at angles to match leg angles a challenge. Relax. If off a bit, drill a slightly larger hole. Which would be no issue if the washers were a tad larger. 4. And the biggest one: the rack comes with a sticker limiting weight to 5 lbs. Even Honda isn't THAT conservative. |
|
Installed these pegs this morning - substantial feel, quality fit, first-rate appearance. I found the instructions murky - literally - in that the photos were dark and, in one case, the written instructions pointed me to the wrong photo...cost one star in my rating. I'd also suggest adding pictures of the hardware to the "Included" list and clarifying the use of the three different washers. The assumption on Kuryakyn's part that installers will recognize the arcane references to the various fasteners makes little sense. I don't recognize a BSCS vs HHCS fastener. Also, the parts list indicates that the two major fasteners are the same diameter/thread pitch. They aren't! Finally, this accessory comes with several subassemblies pre-assembled- you won't find all the listed parts in the box unless you take these apart. These cost the pegs a second star. One personal preference - I found mounting the 2nd peg easier as I assembled it before attaching it to the bike. Looking forward to a trial ride soon! |
| I ordered the other intake vents and didn't like the way it looked so I ordered this one and what a difference it makes the front look. It fits with no gaps on mine. Glad I exchange,it looks great to me. Got some compliments on it also. It adds that extra little class to the front of the bike. |