Contact Us
| Will they fit in the rear of a 2016 GL1800 |
| My 2009 Goldwing had 17k mile on it when I did this a few months ago.....I replaced the spring and hydraulic line. What I discovered was that over the 10 years of ownership that most of the oil in the slave unit had “seeped†by the slave piston....not a true leak.....the slave unit wouldn’t start to compress the spring until #15 on the position indicator. Once replaced and bled, I can hear the pump start to labor @ # 4 now. Well worth the time spent to install. |
| I was contacted via Wingstuff.com messaging. CL from BigBikeParts asked me to send my cover to him. I received a new cover for about a fourth of what the original cost. Just goes to show that writing a review on WingStuff.com is worth the effort. |
| Disappointing. C’mon guys. |
|
These do only slightly good for fixing the front end of the Wing. Real solution is a new tapered roller bearings in steering stem for $40 You'll be glad you did. |
| The description says running and brake lights however I don't seem to get any brake action out of the lights. Otherwise they are looking great on the back. I used a lot of grease, wrapped all connections thickly and completely in electrical tape, and secured them high and left in the compartment out of the path of wheel spray. I hope they last. |
| Just installed these on my high beams. (2004 GL1800) This completes the change over. I had oscillators on the original high beams. I removed them before I installed the pathfinders. This is a much harder installation than the low beams. I ended up taking the shelter off. Some more talented folks most likely will tell you that they can do it without removing the shelter. I also ended up replacing the air filter while I was this deep into the bike. I am not a mechanic and It took me several hours to complete the job. Now for the results. I really do like them. Much brighter and the light pattern seems to be wider. Not sure if they project out as far as the original or not. I recommend if you are going to do the change over I would do both high and low beams. |
|
Remove the front wheel. There are 2 hex bolts in the front and 2 bolts in the back. The fender slips out from between the forks. |
|
FINAL REVIEW FOR THIS SET OF TIRES AT END OF SERVICE Just replaced this set of E-4's. Mileage was 17,424 on the rear and 11,372 on the front. They were balanced with balance beads and the pressures were ran at 42 front and 44 rear. Riding consisted of a mix of mountains. ( I live in Maggie Valley N.C) and highway. Several trips of 2-3k miles each. On these trips I did pull a Bushtech trailer. I replaced this set with a exact replacement inclusive of new valve stems and balance beads. I would recommend them with the understanding that they will get somewhat noisy near the end of service life. The tires I pulled off were still considered safe but were down to the wear bars. |
| Just replaced this set of E-4's. Mileage was 17,424 on the rear and 11,372 on the front. They were balanced with balance beads and the pressures were ran at 42 front and 44 rear. Riding consisted of a mix of mountains. ( I live in Maggie Valley N.C) and highway. Several trips of 2-3k miles each. On these trips I did pull a Bushtech trailer. I replaced this set with a exact replacement inclusive of new valve stems and balance beads. I would recommend them with the understanding that they will get somewhat noisy near the end of service life. The tires I pulled off were still considered safe but were down to the wear bars. |
| This is my first set of riding boots I've owned. I was a little skeptical after reading the reviews, especially about the fit, but they fit fine. A little snug when I first put them on but quite comfortable after that. I was more concerned with how warm my feet may get in hot Florida weather, but they were no hotter than my leather boots. I'm very satisfied. |
| I've had these lights installed for several months now and absolutely no problems. Excellent quality, no need for new cowl, or springs or glue to hold it in place. When installing it's a bit hard to tell up from down, but I took my time and it fit perfectly. I would definitely recommend this product. |