-
Volt Meter With Back Panel
By WingStuff SKU: WSVOLTMETER
- $79.99Save $14.96
MSRP: $94.95
-
-
-
Your Bike
Will this fit your bike?
-
Related Items
43 Member Reviews
1 Star: 0
2 Stars: 2
3 Stars: 3
4 Stars: 5
5 Stars: 33
Volt Meter With Back Panel
ITEM CODE: WSVOLTMETER, SKU: WSVOLTMETER
12.09.2018
Looks factory installed
I've been shopping for a while for a voltmeter not sure of type or style. I decided on this one as it is OEM quality and surly will fit my 2013 F6B. Installation was a breeze using the recommended extension. I simple fished the line from the left pocket to the right pocket. I did have to repair the connections on the back of the voltmeter as they broke off during installation. I love the back lit red light and the gauge needle is smooth and steady. A bit pricey but I like the factory look that it has. |
Volt Meter With Back Panel
ITEM CODE: WSVOLTMETER, SKU: WSVOLTMETER
08.19.2018
Installed on 2006 GL1800
Excellent quality and fit. Works very well. The only thing I can complain about is not the voltmeter's fault. The red access plug for the voltmeter was on the left side instead of the right. As suggested, I did buy the extension, which I did use. Had to run the wiring from under the left pocket to under the right pocket. With a little ingenuity, I got it done without the wiring showing too much. Everything was plug n play as advertised and the voltmeter works very well. |
Volt Meter With Back Panel
ITEM CODE: WSVOLTMETER, SKU: WSVOLTMETER
08.10.2018
Installed on 2017 GL1800
The installation instructions are not fully accurate for a 2017, but I figured it out. I was able to get the molding piece off by taping the paint, popping the corner with my fingers, and then used a wooden shim to hold up the corner and another wooden shim at the center of the bottom (where the clip is) to get the clip to let loose. That was the hardest part. Getting the lock off is pretty easy. I removed the clip on the back that was holding it on the plastic and that allows for removing the cable. You have to order the extension wire mentioned. The accessory power is on the other side of the bike. So on the clutch side of the bike I removed the storage compartment. You don't need to fully remove the molding piece for that, just get the thin part loose. I then fished the extension wire across the bike with a long zip tie. That worked well. To put the lock in the new panel I removed the voltmeter first. Then reassembled everything. Took me a couple hours but I'm slow and cautious. |
Volt Meter With Back Panel
ITEM CODE: WSVOLTMETER, SKU: WSVOLTMETER
04.25.2016
Nice after all said and done
I ordered this item after reading all the reviews (and having to replace my battery). After all said and done , I'm happy with it. I was however very disappointed in the instructions, because there were none. I have a '14 wing and all the reviews talked about 05-10 wings, so researching the instructions became tire some. The instructions are a PDF on the website, but are simply useless. After installing the gauge I learned the back post was touching my radiator and the wire coming off the post was resting against the radiator. I had to bend the wire terminal to the light to make it clear the radiator and I had to reposition the hot wire as not to rest on the radiator, it barely fit. I ordered the recommended t harness so I would have plug and play. After finally locating the factory plug on the clutch side, I spent an hour trying to figure out how to use it. Now you're probably thinking I'm a moron by now, but I have done 12v electric work for years. But the fitting did not match up but one way, in which using that way reversed the polarity going to the meter. I finally figured they had to have screwed it up when manufacturing the t harness, so I took the wires out of the plug and swapped them around to achieve the proper connection. Just a good thing I was paying close attention. If you order the t harness, watch closely that black goes to black and red goes to red. Once I corrected those issues, works and looks great. |
Volt Meter With Back Panel
ITEM CODE: WSVOLTMETER, SKU: WSVOLTMETER
03.16.2016
Installation Voltmeter
Please see my previous review. I contacted Wingstuff and talked to the manager, Rodney, and his primary concern was to make certain I was taken care of. Wingstuff immediately sent me a new voltmeter as well as the new wiring harness. I returned to the dealer who had originally installed the voltmeter and the voltmeter and back light are now working fine. The dealer, Champion Powersports completed the additional installation at no charge. Thanks to all. I would suggest that special comments be made relative to the installation of this unit on 2010 Goldwings. |
Volt Meter With Back Panel
ITEM CODE: WSVOLTMETER, SKU: WSVOLTMETER
02.19.2016
Installation voltmeter
Was unable to install the volt meter on my 2010 Goldwing. The red plug referred to in the instructions was far out of reach. Had to have a dealer remove the body covering engine etc to install. Additional cost was $120 and the meter is not lighted as shown in the ad. |
Volt Meter With Back Panel
ITEM CODE: WSVOLTMETER, SKU: WSVOLTMETER
12.10.2015
A must have.
I used to have a little LED display, but in direct sunlight it was hard to see. I installed this setup yesterday. Absolutely plug n play. Very accurate. Highly recommended mod. I likey! |
Volt Meter With Back Panel
ITEM CODE: WSVOLTMETER, SKU: WSVOLTMETER
01.28.2015
Looks Like OEM & Works Well
I have had this Volt Meter With Back Panel on my bike now for about a year. This is an easy install, the panel/meter look factory installed. The meter is easy to read day or night with nice red back lighting. My only minor issue is that the meter is apparently dampened electrically and takes a few seconds to start indicating, not an instantaneous response like I would have expected. I would recommend this product! |
Volt Meter With Back Panel
ITEM CODE: WSVOLTMETER, SKU: WSVOLTMETER
10.29.2014
Nice Addition
Good fit with a nice factory appearance. Pretty much a plug-n-play installation on my '05. As others indicated, you have to drop the meter out of the back panel to install the lock retention clip. Be nice if that was mentioned in the instructions. Not a big deal, added 5 minutes to the 30-minute install. Radiator relief hose had to be slightly rerouted to accommodate gauge intrusion. Back-lighting is red. Would be sweeter if it was color-matched to the factory instrumentation. Still a nice addition to anyone's arsenal of gadgets. |
Volt Meter With Back Panel
ITEM CODE: WSVOLTMETER, SKU: WSVOLTMETER
01.06.2014
Good Product
Good looking, useful addition and easy to install; just print and follow the PDF instuctions. I liked how the wiring is designed to fit the standard heated grips socket, which is directly under the standard panel, thus making the connecting up of the meter very easy. |
Volt Meter With Back Panel
ITEM CODE: WSVOLTMETER, SKU: WSVOLTMETER
09.22.2013
OEM Looks
This is also what I did. Be sure and get the extended pigtail to be able to run the power connection back over to the left fairing pocket area. That way, everything pretty much stays OEM and it's plug'N'play .......... |
Volt Meter With Back Panel
ITEM CODE: WSVOLTMETER, SKU: WSVOLTMETER
03.10.2013
OEM look, quality and function
I got this to replace the original cover here on my Wing that the previous owner had mounted something to (left 4 holes behind). Why this is a great product: 1. Very easy to install. 2. Plug and play. 3. Perfect OEM fit & finish. 4. Voltmeter is very functional and accurate. 5. Looks classy and is lit up/visible at night. Another item that you have to wonder why it isn't OEM from the factory? |