- Your Price
- Item #:
Fits Low OR High Beam. If you want to upgrade BOTH Low and High Beams you will need to order 2 sets.
Upgrade your stock lighting and experience LED lighting like never before. This LED lighting simply makes you more visible during the day and if you ride at night, you will certainly appreciate the changeover. This setup upgrades your lights to bright white (6000k) while making you more visible on the road day or night, they draw less power from your battery which in turn reserves your charging system for other electronics.
You will certainly appreciate the changeover and REPLACING your headlights to LED is one of the best investments you can make on your bike. Be Safe... Be Seen..!
You can either replace your Lo Beams, your High Beams or Both. Each kit includes 2 High Performance LEDs w/inline drivers and can be installed in either setup.
Unlike other lights on the market these lights have been fit checked and road tested by seasoned riders/enthusiasts so you can be assured you are getting a high quality product for your bike.... Seriously improves your lighting experience.
LED lighting draws very little amperage while outputting a great light down the road. Unlike other LEDs that are just bright to look at these LEDs throw a fantastic beam down the road.
Improved Jet-pro type heat-sink that efficiently absorbs and moves heat away from the LED. Installation is even easier than before, no trimming/cutting of the rubber boot is required.
These lights are also much cooler than competing models. Better design, better value, better product!
NOTE: Some items in the image shown/video may look slightly different from the actual parts you receive. The product(s) you receive may either be an upgraded, improved or simply a re-designed model compared to what was used in the image/video but delivers the same or better quality.
LED KIT INCLUDES: LED lights w/inline Driver, installation instructions.
(1 KIT) Replaces your LOW OR HIGH BEAMS: Includes (2) PATHFINDERLED LEDs w/inline LED drivers.
(2 KITS) Replaces your LOW AND HIGH BEAMS: Includes (4) PATHFINDERLED LEDs w/inline LED drivers [Add $110.00]
INSTALLATION INSTRUCTIONS WITH VIDEO INSTALL LINK
1-YEAR WARRANTY FROM DATE OF PURCHASE (BUY WITH CONFIDENCE). RECEIPT REQUIRED
Fitment: (GL1800) 2001-2017 and F6B motorcycles.
You’ve probably heard of LEDs that don’t throw a good light down the road and that’s true, most don’t. Unlike other LEDs on the market that simply do not throw enough light, these LEDs will certainly do the JOB. New Generation LEDs are designed to be used in headlight housings and will certainly satisfy your lighting needs.
Guaranteed you will be blown away compared to your stock bulbs!
Rode about 50 miles tonight after dark. These are definitely a improvement over the stock lights in my opinion. I would suggest that you watch a couple videos on the characteristics of LED lights before you change over. I plan on upgrading the high beams before spring. Also if you do change over I suggest setting the headlight height adjuster to low as this helps with the light pattern.
I just put these in tonight on my low beams. The install wasn't really that hard. This is assuming you have changed the bulbs before and understand the whole doing it by feel thing. I suggest putting the bike on the center stand in order to keep the retainer clips back during installation. I took a short ride afterwards. The light is brighter but I don't think the down the road projection is what I expected. I will reserve judgement until I can get some miles on them. I do think they will be more noticeable
during the day.
These lights are the hot ticket. You heard the expression seen or be seen. These are it. Install is tricky, watch the install video . After you studied the install video.
I tried it there way , what a S.O.B on the left side. The right side I removed the panel that covers the key switch. Gives you that much more room to work with. Thread the wire from the LED Driver through the heat sink. through the factory rubber boot then attach it to the led Light wire. Install the LED light in the socket and secure the attachment spring to the bulb . Then the rubber boot. Then the Heat sink. ( CAUTION ) The heat sink has a 0.50 hex allen screw in it. It might be to tight . Give it 1/6 of a turn counter clockwise. Technical phone number for so/cal - Pathfinder is 5629913868 Awesome great advice from them.
And we can't wait to show you how it's done!
Save on shipping! Will Call is available at our Southern California headquarters.